TNM7000 ECU-KIT Car Programmer

You are here:

Home
Portfolio
TNM7000 ECU-KIT Car Programmer

TNM7000 ECU-KIT Car Programmer

Categories: Programmer

TNM7000 ECU-KIT Car Programmer

TNM 7000E 4-in-1 CAR Programmer

ECU-KIT Software : ECU , Immobilizer, Dashboard programming through JTAG /ISP/BDM /GPT. OBD Cable Downloading.
Universal programmer: Supporting 25000 Devices (Flash NOR/NAND/SPI , EEPROM , MCUs , CPLD and EMMC).
ECU Remap software: ECU tuning + checksum calculation.
CAN Analyzer software: for diagnosing CAR CAN-BUS problems and reverse engineering.

with Free ECU-KIT car programming Software:

Supporting OBD/JTAG/ISP programming of Bosch, Delphi, Continental, Siemens, Denso, Mitsubishi, Valeo , Sagem , Magneti Marelli and many other units with wiring diagram and checksum calculation. Support of most MCUs Used in Car ECUs , Immobilizers , BCM , UCH , ABS , AirBag including:

Full Motorola(Freescale) 9S12 series with unsecure capiblity / Infineon Tricore TC17xx series with password reading for many ECUs / Hitachi SH705x read and write / Full Microchip PIC & DSPIC support / Full Atmel microcontrollers support / NXP PCF79xx remote chips / Renesas R5F10Dxx (Secured EEPROM read + Write) / NEC upd70F3xxx series support / NEC UPD78F0828-937-949 Dashboard / NEC UPD78K0 Dashboard External/Internal EEPROM Read write through MBUS / Infineon XC233x , XC236x MCUs used in AirBags / Fujitsu MB91F06x /Cypress S6J & MB91F5xx MCUs used in Dashboards.

ISP Protocols: Tricore Boot / Aurix TC27x JTAG / Bosch GPT (without ECU opening) / ST10F Boot Mode (Kline & ISP) / Motorola BDM with 9S12 Glitch security removal capability / Denso 76F00xx NBD / MPC5XX BDM / JTAG MPC5XXX / JTAG SPC56xx / Mitsubishi Boot / NEC MBUS / NXP FS32K142/144/146 / Renesas RH850 Unlock .

OBD Downloader and Reading with Checksum calculation (or Bench mode):

Bosch: BoschMe7 / BoschM7.8 / Bosch Me7.9.7 / Bosch Me17 China / Bosch Me17.9.7 / Bosch EDC17C53 / Bosch EDC17C39 / 4.5 (Flash&EEprom) / Bosch(Me7.4.4 Flash&EEprom) / Bosch M7.4.4 / Bosch M7.4.9 / Bosch M7.4.11 / Bosch MG1CS1 / Bosch CPGDSH2
Bosch for Bikes: Bosch MSE3.0 / Bosch MSE6.0 / Bosch MSE8.0 / Bosch MSE2.0 (MG1CA094)
Continental: Hyundai & Kia SIM2K250 / SIM2K260 / SIM2K251 / Sim2K-141 / Sim2K-24x / Sim2K-34x / Renault EMS3132 (Flash & EEPROM) / EMS3134 .
Cummins for trucks: CM2150 / CM2220 /CM554 / CM876
Delphi:Delphi MT92.1 / Delphi MT62.1 / Delphi CRD2.35 / Delphi MT86 / Delphi MT38 / Delphi MT60 / Delphi MT80 / Delphi MT22.3 / Delphi MT22 / Delphi MT22.1 / Delphi MT20U2 / Delphi MT05-1 / Delphi MT05-2/ Delphi MT05-3
Denso for Toyota: GEN 1 + virtual online read + CUW converter / Gen2-P5CAN
Hitachi: Nissan (2005-2018)
Mitsubishi: Mazda3/6 (E6T6xxxx) , Mazda3 (E6T5xxx)
SAGEM: Renault S3000 / Peugeot S2000
Valeo: Peugeot PL4 / J34 /J35

Remap and ECU Tuning: Remap Tables and 2D & 3D Views + Checksum calculation.

Free software upgrade with no Subscription Fee . Windows XP/VISTA/7/8/10/11 (32,64 bits) Support.

Programmer Software:

25000 Supported Devices Flash Memory (Parallel / Nand /Serial) , EPROM , EEPROM , Serial EEPROM , Microcontroller , NVRAM , FRAM , PLD).

48-Pins ZIF Socket with Pin Continuity tester & 10-Pins ISP/JTAG Connector.
USB 2.0 High Speed ,Read EMMC /Nand Flashes with 12Mbyte/Sec , Reading Serial Flash memory with 8 Mbit/Sec.
Auto detection of all flash Memories/Microcontrollers with Device ID.
Multiple Programming is possible by attaching 2 or more Programmers to one PC.

Low cost adaptors , works with many different adaptors from other programmers.